• Email Support info@americanblowerllc.com
  • Call Support (713) 360 6995
American Blower LLC

Posts

Positive Displacement Blower is Used in Many Types of Pneumatic Conveying and Process Systems.

A positive displacement blower is used in many types of pneumatic conveying and process systems. This important equipment is forgotten until it fails. Once the blower fails, it is up to the maintenance personnel to get the system back online. Regular maintenance can often prevent damage to the blower.

PD blowers operate with a motor driving dual eccentric impellors usually via a pulley and belt transmission system. Dual impellors counter rotate within a cast iron casing. The air within the casing fed through an inlet is trapped between the impellors and the casing and with each revolution the air (or gas) is forced out of the discharge against whatever pressure exists in the system.

The clearances between the rotors and the casing parts are important if the efficiency of the positive displacement blower services Houston is to be maintained. With continuous operation the rotating parts gradual wear of and have to be properly maintained.

Regular maintenance programme will increase the life of the machine and minimising downtime. Checking belt tensions, oil levels, monitoring vibration frequencies, cleaning filters, checking relief valves and leaks etc. regularly helps in increasing their life.

Starting and running a PD Blower USA low on oil result in almost immediate failure of the gears. Once the gears begin to fail, the Rotor lobes will clash, end clearances will change, thrusting the driven rotor into the free end plate and failed bearings, causing the rotor lobes to clash even further.  If detected early, the blower is rebuildable.

The most critical ingredient to blower maintenance is proper lubrication. If not properly lubricated, damage sets in early. It is important not to run or start a PD blower services when it’s low on oil because the gears will fail which results in the clash of the rotor lobes making the bearings fail.

If the application involves a corrosive process gas, you may find that your blowers quickly need to be replaced as the interior components of the blower are corroded over time by the gas.  In these applications, special coatings or materials can be added to your blower to help protect your equipment and extend its lifespan.

If a critical wear and tear is noticed on the PD blower’s rotating parts it is highly recommended to have a full-service check and a full-service repair to avoid irreparable damage. The PD blower will be disassembled and the seals, bearings and other parts will be thoroughly inspected and repaired at an experienced service centre. Attention should be given to the repositioning of shims, dowels, retainer rings, O-Rings, lubrication, fasteners and fittings.

Some of the key players operating in the global industrial blowers market are Gardner Denver Inc., Hoffman & Lamson, SPX and others. While in pumps Nash, Gardner Denver, Hoffman & Lamson, Sutorbilt, and Roots among others contribute to the major share in the market.

American Blower LLC provide services for any brand or manufacturer of pumps. Our services range from standard inspections and repairs to complete overhauls. A repair or overhaul of a pump generally consists of an inspection and repair/modification. Some of the key players operating in the global industrial blowers market are Gardner Denver Inc., Hoffman & Lamson, SPX and others. While in pumps Nash, Gardner Denver, Hoffman & Lamson, Sutorbilt, and Roots among others contribute to the major share in the market.

We rebuild all types of pumps and blowers to bring its operation back to OEM specifications. The technicians have been factory-trained in the process of vacuum pump repair. After the repair or remanufacturing process is complete, each item is system tested to ensure proper operation, OEM specification verification, and extended operation under load and also with stocks of spares to support older or obsolete equipment which OEM no longer supports. We use only OEM parts for repairs to ensure the highest quality of work and extend the life of your equipment. You can repair, rebuild, or exchange your pump with our replacement program.

Please contact us for all your requirements on blowers or pumps call us at (713) 360 6995 or mail us at info@americanblowerllc.com. We are based in Houston, Texas and our skilled technicians will address all your queries.